Point d’Arrêt

There is something exceptionally satisfying about landing a touch on one’s opponent and having it stick as if dueling with sharps. Rather than a button skipping off-target when landed with a glancing angle, there can be no question about the validity of a touch when your tip grabs its target as if it were exposed flesh on the dueling grounds at dawn.

How can this degree of realism be achieved within the relative safety of the salle?  In lieu of a rubber button, one mounts his or her dueling sword with a point d’arrêt (pronounced “pwan de-ray” — literally meaning stop-point), and duels with the added protection of a manchette on the weapon arm.

Point d'Arrêt

Points d’arrêt are forward-facing, sharp metal teeth mounted on the nail-head of a dueling sword.

What exactly are points d’arrêt? They are a trio of sharpened, forward-facing metal teeth mounted on the nail-head of an épée (dueling sword). When one or more of the teeth land on the intended target, the teeth hold fast to the fabric. Given the use of sharpened teeth, it is essential that a sacrificial manchette protect the entire weapon arm — the nearest target. This also plays into the psychology of dueling with points d’arrêt; the sharp teeth make one immediately aware of the risk  faced with sharps, and the prudent fencer shifts mainly to the forward targets of the hand and forearm to reduce one’s own target exposure to your opponent’s point d’arrêt.

Given the relative rarity of classical fencing compared to sport fencing, the use of point d’arrêt with dueling épée is quite a rare occurrence, and their manufacture even more rare.  Rockwell Classical Fencing does produce them. However, in the interest of historic preservation and education, the aim of this post is to illustrate how I manufacture points d’arrêt with basic workshop tools. I have done so by following the gracious advice and techniques given to me by master swordcutler, Dennis Graves of No Quarter Arms.  His manufacturing techniques are elaborated upon and illustrated here with his permission — and with my sincere thanks.

A Disclaimer
The manufacture and use of point d’arrêt presents an elevated level of risk of damage to fencing jackets and gloves, and an elevated risk of accidental physical harm.  One should never use point d’arrêt against an opponent without protective gear in addition to standard fencing equipment, including protective manchettes. What is contained herein is how and what I do. Any choice to follow the steps illustrated here to manufacture, mount, or to use points d’arrêt are done at your own risk.

Tools & Materials for Manufacture

  • Bench Vice
  • Drill  Press (or stout drill and means to securely clamp it)
  • Grinding Belt
  • 6-inch 3-square smooth-cut file
  • 3 1/2″ flat smooth-cut file
  • 8 or 10-inch smooth-cut flat file (helpful, but not necessary)
  • Hacksaw
  • 1/4″ 20 x 1″ Allen-head Capscrews

The capscrews are heavy modified and formed  into points d’arrêt.  Plan on extras since you will likely use a couple to get the procedure and your technique honed.

For an enlarged view of each step to create point d’arrêt, click on any photograph in the two galleries below.

 

In addition to illustrating the manufacture of points d’arrêt, I have also attempt to illustrate how I mount them to an épée’s nail head. My mounting process is based on the very little I have been able to find published on the web, my tying and lashing experience, and the advice of Scott “Doc” Lucchese, CCF’s Médecin de Salle.

 

As always, your feedback and/or advice would be welcomed either by submitting comments to this post below or via the Columbia Classical Fencing page on Facebook.

Advertisements
This entry was posted in Equipment, Weapons and tagged , , , , . Bookmark the permalink.

5 Responses to Point d’Arrêt

  1. obersaber says:

    Great article,do you have a recipe for the ink used with these points?

    • Scott says:

      I do not, but I will ask around and let you know. We use the points merely to grab the manchette, and they work quite nicely for that.

    • Scott says:

      After doing some research, it would appear that phenolphthalein was used. A diluted basic paste was daubed onto the tip, showing color when landing a hit. The color can apparently be removed by applying an acid, such as daubing with white vinegar. Caveat emptor: I have not tested this.

  2. Chris O'Keefe says:

    Thank you.
    I found the entire post fascinating.

    While trying to explain our latest chapter to my mother I received a suggestion.

    A drop of rubber cement on the point of the blade might hold the point d’arrêt in place and create a non-permanent bond while securing it with string or floss.

    I have not yet tested this idea.

    • Scott says:

      I would expect that it would help position the point when first tying them onto a nailhead. After tying a few one, one becomes able to steady the point until a few loops secure the teeth.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s